Water

Transpiration

Unit: mm/day

The process by which water absorbed by plant roots moves through the plant and is released as water vapour through leaf stomata — the primary pathway of water loss from a crop canopy.

<strong>What is transpiration?</strong> The <strong>transpiration definition</strong> in agriculture: the movement of water from soil through plant roots, stems and leaves, exiting as water vapour through stomata. Transpiration accounts for 90–95 % of total water use by a crop (the remainder is direct soil evaporation). It is driven by the vapour pressure deficit (VPD) between the leaf interior and the surrounding air, and is regulated by stomatal opening and closing. Potential transpiration is estimated using the Penman-Monteith equation, adjusted by a crop coefficient (Kc). Water stress occurs when soil water supply cannot meet transpiration demand, causing stomatal closure, reduced CO₂ uptake and ultimately yield loss. See the <a href="https://www.fao.org/land-water/databases-and-software/eto-calculator/en/" target="_blank" rel="noopener noreferrer">FAO ETo calculator</a> for reference evapotranspiration estimation.

Factors affecting transpiration rate

FactorLow transpirationHigh transpirationNotes
Vapour pressure deficit (VPD) Low VPD (humid, cool) High VPD (dry, warm) Primary driver of stomatal opening and water loss rate
Solar radiation Overcast / low radiation High radiation / clear sky Drives stomatal opening via photosynthetic demand
Wind speed Still air (boundary layer thick) Windy (boundary layer thin) Increases turbulent transfer of water vapour from leaf
Soil water availability Soil at field capacity Soil below MAD threshold Stomatal closure under water stress reduces T sharply
Crop canopy cover Sparse / early season Full canopy / LAI > 3 More leaf area = more transpiring surface
Crop coefficient (Kc) Early season (Kc ≈ 0.3–0.4) Mid-season (Kc ≈ 1.0–1.2) Kc adjusts reference ET₀ for actual crop characteristics

Transpiration and the water balance

Transpiration is the dominant pathway of water loss from a growing crop — accounting for 90–95% of total evapotranspiration once the crop canopy has closed. The remainder is direct evaporation from the soil surface, which is most significant early in the season when the soil is bare or partially covered. Irrigation management targets replacement of the combined evapotranspiration loss: tracking daily ET and subtracting effective rainfall gives the accumulating soil moisture deficit (SMD) that must be managed to avoid yield-limiting water stress.

The available water capacity (AWC) of the soil determines the total water reservoir that a crop can draw on before stress develops. AWC combined with daily ET rate determines how many days of dry weather can be tolerated before irrigation is required. See the irrigation scheduling guide for the practical SMD management approach.

Stomatal regulation and stress responses

Plants regulate transpiration through stomatal opening and closing — a rapid response to VPD, light intensity, CO₂ concentration and abscisic acid (ABA) signals from water-stressed roots. When soil dries below the maximum allowable deficit (MAD), roots signal drought stress via ABA, causing stomatal closure before visible wilting occurs. This stomatal closure is protective but immediately reduces CO₂ uptake and photosynthesis, limiting growth and yield. See the stomatal conductance glossary entry for the physiological detail and soil water potential for the soil-side mechanism.

Transpiration in practical irrigation management

In UK field crops, transpiration-based irrigation scheduling is the standard approach for high-value crops (potatoes, onions, vegetables). The calculation chain is: weather station data → Penman-Monteith ET₀ → Kc adjustment → daily ETc → cumulative SMD. When SMD reaches the threshold for the crop and soil type, irrigation is triggered. The crop coefficient and effective rainfall glossary entries cover the two key adjustments in this calculation. See the potato irrigation management guide and irrigation scheduling guide for full scheduling programmes.

Frequently asked questions

What is the difference between transpiration, evaporation and evapotranspiration?
Transpiration is the loss of water vapour through plant leaf stomata — a biological process controlled by the plant. Evaporation is the physical loss of water from soil and wet surfaces — it is driven purely by energy and vapour pressure deficit, not by plant physiology. Evapotranspiration (ET) is the combined total of both processes — the total water loss from a vegetated surface to the atmosphere. In practical irrigation management, ET is the quantity that must be replaced by rainfall and irrigation to maintain soil moisture above the deficit threshold. The Penman-Monteith equation estimates reference ET₀ (from a hypothetical grass reference surface), which is then adjusted by the crop coefficient (Kc) to estimate actual crop ET. See also effective rainfall for how natural rainfall offsets the ET demand.
How is transpiration measured or estimated on farm?
On-farm transpiration is not directly measured — it is estimated from weather data and crop models. The standard approach is: (1) use a weather station to calculate reference evapotranspiration (ET₀) using the Penman-Monteith equation; (2) multiply ET₀ by the crop coefficient (Kc) for the current crop stage to get actual crop ET (ETc); (3) subtract effective rainfall to get the soil moisture deficit (SMD) accumulation. Soil moisture sensors (capacitance probes, neutron probes) measure soil water content directly and provide validation data. For practical irrigation scheduling, organisations including AHDB ↗ and the Irrigation Research Management Unit provide ET data by location for UK crops. See the irrigation scheduling guide for the practical application of ET-based scheduling.
What happens to crop yield when transpiration demand exceeds water supply?
When soil water supply cannot meet transpiration demand, the plant responds by closing stomata to limit further water loss. Stomatal closure has a direct yield cost: CO₂ cannot enter the leaf through closed stomata, so photosynthesis falls immediately in proportion to the degree of closure. Sustained water stress (stomata closed for hours per day) reduces carbon assimilation, slows leaf expansion, and can abort flowers and young fruits. The yield penalty depends on the crop, growth stage, and stress duration: cereals are most sensitive at anthesis and grain fill; potatoes at tuber initiation and expansion; maize at silking. A useful rule of thumb for UK potatoes is that each 25 mm of unmet irrigation demand costs approximately 1–1.5 t/ha of marketable yield. See the potato irrigation management guide and soil water potential for the physiological mechanism.
How does VPD affect transpiration and why does it matter for irrigation timing?
Vapour pressure deficit (VPD) is the difference between the saturation vapour pressure at leaf temperature and the actual vapour pressure of the surrounding air. When VPD is high (hot, dry, windy conditions), the gradient that drives water movement from leaf to atmosphere is large — transpiration rate increases. When VPD is low (cool, humid, still), the gradient is small — transpiration rate is low. For irrigation timing: on high-VPD days, crops transpire rapidly and soil moisture deficits accumulate quickly; on low-VPD days (or at night), transpiration is minimal. Practical implication: irrigation systems that apply water based only on a fixed calendar interval can under-supply in high-VPD periods and over-supply in cool periods. ET-based scheduling adjusts to actual weather conditions and is the most water-efficient approach. See the stomatal conductance glossary entry for the leaf-level mechanism.
Does transpiration differ between soil-grown and hydroponic crops?
The physics of transpiration — water vapour loss through stomata driven by VPD — is the same whether the crop is grown in soil or hydroponics. The key difference is water availability: in soil, water is held at varying tensions and becomes increasingly difficult to extract as soil dries; in a hydroponic substrate (rockwool, coir, perlite), water tension is managed precisely by irrigation frequency and volume. Protected crops in glasshouses also experience fundamentally different VPD environments from outdoor crops: temperature and humidity are partially controlled, meaning transpiration rates are more predictable and the response to irrigation management is more precise. In a glasshouse, transpiration can be estimated from temperature and humidity sensors, with irrigation events triggered by cumulative radiation (light-driven transpiration triggering). See the tomato irrigation and water quality guide for the protected cropping application.