Water

Soil water potential (Ψ)

Unit: kPa or MPa

The energy status of water in the soil — a measure of how tightly water is held by soil particles and how readily plants can extract it.

Soil water potential is expressed as a negative pressure (matric potential). At field capacity, matric potential is approximately −10 kPa; at permanent wilting point it is approximately −1,500 kPa. As soil dries, water potential becomes more negative and plants expend more energy extracting water. Tensiometers measure soil water potential directly in the field.

Soil water states and plant availability

Water stateMatric potentialSoil conditionPlant availability
Saturated 0 kPa All pores filled with water Waterlogged — anaerobic risk
Field capacity −10 to −33 kPa Macro-pores drained; micro-pores full Optimal — easily available
Moderate stress −100 to −300 kPa Soil visibly drying; some water still available Plants begin to stress
Permanent wilting pt −1,500 kPa Water held too tightly for roots to extract Zero — plants wilt permanently
Air-dry −10,000 kPa Very thin films of water on particles None

Why water potential matters more than water content

Plant roots cannot "see" how much water is in the soil — they respond to the energy needed to extract it. A clay soil and a sand soil can both be at 20% volumetric water content, yet the clay soil may still have abundant available water (wide pores emptied, micro-pores still full at moderate tension) while the sand is near wilting point (most water already drained by gravity). The matric potential captures this difference. It is why irrigation scheduling based on soil water potential — via tensiometers — is consistently more precise than scheduling based on fixed calendar intervals or even volumetric water content alone.

The available water capacity (AWC) of a soil is the difference in water content between field capacity (typically −10 to −33 kPa) and permanent wilting point (−1,500 kPa). A soil with high AWC stores more water that plants can use between rain events. See the irrigation scheduling guide for how AWC and soil water potential are used together.

Tensiometers in practice

A tensiometer consists of a water-filled tube sealed at the bottom by a porous ceramic cup. When inserted into the soil, water moves through the ceramic in response to the soil's matric potential. As the soil dries, water is drawn out and a negative pressure (vacuum) develops inside the tube — measured by a Bourdon gauge or pressure transducer. Tensiometers are best suited to soils where the matric potential stays in the measurable range (0 to −85 kPa) during the growing season — they are most useful in irrigated crops (potatoes, vegetables, soft fruit) where the target is to keep soil potential in the −20 to −50 kPa range. Install tensiometers at the rooting depth of the crop (typically 20–30 cm for shallow-rooted vegetables, 30–45 cm for potatoes). See the AHDB irrigation scheduling guide ↗ for installation guidance.

Frequently asked questions

How is soil water potential measured in the field?
Tensiometers are the most common field instrument for measuring soil matric potential in the range 0 to −85 kPa. A ceramic-tipped tube filled with water is inserted into the soil — as the soil dries, it draws water from the tube, creating a negative pressure (tension) measured by a gauge or electronic sensor. For drier soils (below −100 kPa), gypsum blocks or capacitance sensors measure the electrical resistance or dielectric constant of the medium, which is related to water content and potential. The AHDB irrigation scheduling guidance ↗ explains tensiometer installation and interpretation for potato and vegetable irrigation management.
What is the difference between soil water potential and soil water content?
Soil water content (volumetric or gravimetric) is a physical measurement of how much water is present — litres per litre of soil, or grams per gram. Soil water potential measures the energy status of that water — how tightly it is held and how readily plants can extract it. The relationship between the two is the soil water characteristic curve (also called the pF curve), which differs between soil types. A clay soil at 30% volumetric water content may have a matric potential of −150 kPa (moderate stress); a sandy soil at the same water content may already be near wilting point. This is why water potential is more informative than water content alone for irrigation scheduling decisions. See also the available water capacity glossary entry.
At what soil water potential do crops start to suffer water stress?
The threshold varies by crop and development stage:
  • Potatoes: irrigation trigger typically −30 to −40 kPa in light soils; irrigation becomes critical at −60 kPa
  • Vegetables (lettuce, carrots): trigger at −20 to −30 kPa
  • Cereals: more drought-tolerant; typically triggers at −60 to −100 kPa in flowering and grain fill
  • Maize: particularly sensitive during tasselling and silking — maintain potential above −60 kPa in these periods
AHDB irrigation scheduling ↗ provides crop-specific deficit thresholds. See the irrigation scheduling guide for how to use these thresholds in practice.
What is the total water potential and how does matric potential fit in?
Total water potential is the sum of several components: matric potential (Ψm — water held by capillary forces in soil pores), osmotic potential (Ψs — water held by solutes), gravitational potential (Ψg — height above a reference point) and pressure potential (Ψp — relevant in saturated conditions). In unsaturated agricultural soils, matric potential dominates and is the component measured by tensiometers. Osmotic potential becomes important in saline soils or when soluble fertiliser concentrations are high — plants must work harder to extract water even if matric potential is adequate. See the effective rainfall glossary entry and the crop coefficient entry for how potential links to crop water demand.
Can I estimate soil water potential from weather data instead of sensors?
Yes — soil water potential can be estimated from the soil moisture deficit (SMD), which is calculated from rainfall, potential evapotranspiration (PET) and soil water-holding capacity. SMD modelling uses the Penman-Monteith equation (or a simplified version) with meteorological inputs from local weather stations or gridded weather data. Tools like the AHDB irrigation management tool ↗ and commercial systems (Sencrop, Pessl, DTN) calculate running SMD. SMD modelling is less precise than direct sensor measurement — it accumulates errors over time and may diverge from actual soil conditions after irregular rain events. Best practice is to use SMD modelling to identify the need to check and calibrate against in-field tensiometers.