Grow

Irrigation Scheduling

Irrigation Scheduling guide.

5 min read · Crops:

Why timing matters more than volume

The most common irrigation mistake is applying water too late. By the time a crop shows visible stress symptoms — wilting, rolling leaves, tip burn — yield has already been lost and quality compromised. Effective irrigation scheduling is a preventive activity: you apply water before stress occurs, based on a water balance model that tracks what the soil holds and what the crop uses.

The FAO Penman-Monteith method ↗, described in FAO Irrigation Paper 56, is the global standard for calculating crop water requirements. UK applications use the same framework, with reference ET₀ data available from the Environment Agency ↗ and weather station networks.

The five-step scheduling process

  1. 1
    Determine the soil moisture deficit

    Soil moisture deficit (SMD) is the amount of water needed to return the soil to field capacity. Track SMD using a water balance model: add rainfall and irrigation, subtract crop evapotranspiration (ETc = ET₀ × Kc). Trigger irrigation when SMD approaches the maximum allowable depletion (MAD) for your crop — typically 25–40 mm for potatoes, 40–60 mm for maize.

  2. 2
    Obtain ET₀ for your location

    Reference evapotranspiration (ET₀) can be sourced from a local weather station or from a weather API such as Open-Meteo. ET₀ reflects atmospheric demand — use it as the base for crop water requirement calculations. In the absence of local data, published regional ET₀ values from the Environment Agency or MORECS can be used as a starting point.

  3. 3
    Apply the crop coefficient

    Multiply ET₀ by the crop coefficient (Kc) to get actual crop water use (ETc). Kc varies through the season: low at emergence (~0.3), rising to peak at full canopy (0.9–1.2 depending on crop), declining at maturity. FAO Irrigation Paper 56 provides standard Kc tables. Adjust for local climate and actual canopy cover where possible.

  4. 4
    Set irrigation trigger and volume

    Set a trigger SMD (the point at which irrigation starts) and a refill volume (the amount applied per irrigation event). For most field crops, apply water to refill the root zone to field capacity — avoid both deficit stress and excess that causes drainage below the root zone. For high-value crops like potatoes, trigger at lower SMD and refill more frequently.

  5. 5
    Monitor and adjust in-season

    Soil moisture sensors (capacitance probes, tensiometers, time-domain reflectometry) allow real-time monitoring of actual soil moisture status. Use sensor data alongside the water balance model to calibrate and adjust. Review the model weekly, especially after heavy rain events — a single 30 mm rainfall event can defer irrigation for 7–14 days depending on the stage.

Crop water use through the season

Peak crop water demand in the UK typically occurs in July — when both ET₀ and crop canopy coverage are at their highest. For potatoes, this coincides with critical tuber initiation and early bulking. Daily ETc can reach 5–6 mm/day in warm, sunny weather. AHDB potato irrigation guidance ↗ gives seasonal demand curves and stage-specific SMD limits.

For irrigation decisions, see also the crop coefficient and reference evapotranspiration glossary entries — both underpin the scheduling calculations described here.

Irrigation and water licensing

Water availability in the UK is increasingly constrained during the growing season. Environment Agency abstraction licences ↗ may carry conditions limiting use during drought periods. Investment in on-farm storage (winter-fill reservoirs) is the most effective long-term strategy for securing water availability in dry summer conditions — and is supported in principle under the Sustainable Farming Incentive ↗ framework.

Frequently asked questions

What crops most benefit from irrigation scheduling?
Potatoes, onions and maize (grown for grain or high-quality wholecrop) benefit most from scheduled irrigation in the UK. Potatoes are the most irrigation-responsive UK crop — water stress at tuber initiation and bulking directly reduces yield and quality. AHDB potato irrigation guidance ↗ and the Environment Agency irrigation resources ↗ provide the authoritative UK scheduling frameworks.
What is the maximum allowable depletion (MAD) for potatoes?
For potatoes, the maximum allowable depletion is typically 25–35 mm during tuber initiation (July–August) and can be increased to 35–50 mm during bulking. Exceeding MAD causes bruising susceptibility, quality defects and yield loss that cannot be recovered. AHDB potato irrigation scheduling ↗ provides detailed stage-specific trigger levels by crop type (table, processing, seed).
What is a crop coefficient (Kc) and where do I find values?
A crop coefficient (Kc) converts reference evapotranspiration (ET₀) to crop-specific water use (ETc = Kc × ET₀). Standard values come from FAO Irrigation Paper 56 ↗ — the global standard reference. Values vary by growth stage and local climate. UK-adjusted Kc values are also available from AHDB ↗ and Cranfield University ↗ irrigation research.
Do I need an abstraction licence to irrigate?
In England, abstracting water for irrigation requires a licence from the Environment Agency ↗ unless the volume is below the exempt threshold or the source is a mains supply. During drought conditions, abstraction licences may be restricted. The AHDB water management guide ↗ covers licensing and good practice. Plan water storage carefully — on-farm reservoirs filled in winter offer flexibility during dry seasons.
What irrigation system is best for field crops?
Boom irrigation (rain guns and travelling irrigators) is standard for UK field crops — relatively low capital cost with good flexibility across field shapes. Drip irrigation is used for high-value crops (onions, potatoes in some systems) and gives high water use efficiency but higher capital cost. AHDB irrigation equipment guide ↗ compares systems. The British Crop Production Council ↗ publishes guidance on efficient irrigation management.