Climate

Vapour pressure deficit (VPD)

Unit: kPa

The difference between the amount of moisture the air can hold at saturation (saturation vapour pressure) and the actual amount of moisture the air holds (actual vapour pressure), expressed in kilopascals (kPa). VPD is the primary driver of the evaporative demand on crop canopies and individual leaves — high VPD creates strong atmospheric demand for water, driving rapid transpiration and stomatal closure.

Vapour pressure deficit is calculated as: VPD = SVP − AVP, where SVP (saturation vapour pressure) is determined by air temperature and AVP (actual vapour pressure) by relative humidity. VPD increases with rising temperature and falling humidity — a hot, dry day has a high VPD; a cool, humid day has a low VPD. Understanding VPD is relevant to irrigation scheduling, spray application timing and canopy disease risk management.

VPD and its practical relevance to farm management

Vapour pressure deficit is not a term farmers and agronomists encounter daily, but the concept it measures — the drying power of the atmosphere — underpins several practical decisions that are made routinely in crop management. Whether to spray (is it too dry and windy?), whether to irrigate (how much water is the crop losing today?), and whether to expect high disease risk from a period of humid weather — all these decisions are implicitly about VPD, even when the term is not used.

With weather station technology now widely available and affordable, VPD can be calculated automatically from temperature and humidity data and integrated into spray decision-support apps, irrigation scheduling systems and disease forecasting tools. Understanding the underlying concept makes it easier to interpret the outputs of these systems and to make better agronomic decisions in variable conditions.

VPD and photosynthesis: the water use efficiency trade-off

The interaction between VPD, stomatal conductance and photosynthesis creates a fundamental trade-off in crop water use efficiency. Stomata must be open to allow CO₂ entry for photosynthesis, but open stomata also allow water vapour to leave — and the rate of water loss is proportional to VPD. At low VPD, the concentration gradient driving water loss is small, so stomata can be open and photosynthetically active with relatively little water cost. At high VPD, the same stomatal aperture would cause rapid water loss — so the plant closes stomata partially to limit loss, simultaneously reducing CO₂ supply and photosynthetic rate.

This explains why crops often show midday depression of photosynthesis on hot, dry days — VPD peaks in early afternoon, triggering stomatal closure, even in well-watered plants. Irrigation scheduling that aims to maintain soil water availability during high VPD periods allows stomata to remain more open than they would under stress, supporting photosynthesis and growth at the critical periods when evaporative demand is highest.

VPD in spray application: avoiding the extremes

The ideal spray application window is bounded by VPD at both ends. Too low VPD (below 0.5 kPa, typically early morning or evening in humid conditions): risk of spray drift due to thermal inversions, prolonged leaf surface wetness promoting disease spread, and in some cases poor uptake of systemic herbicides that rely on rapid uptake before rain. Too high VPD (above 2.5–3.0 kPa, typically hot afternoons): rapid droplet evaporation before the spray reaches the target, increasing the proportion of very small droplets (higher drift risk) and reducing the effective dose delivered to the leaf. The target window of VPD 0.5–2.0 kPa aligns with morning or early afternoon application on most UK spray days. See the wheat disease management guide for fungicide timing context.

Frequently asked questions

How is vapour pressure deficit calculated?
VPD is calculated in two steps: (1) Saturation vapour pressure (SVP) from temperature using the Magnus formula: SVP (kPa) = 0.6108 × exp(17.27 × T / (T + 237.3)), where T is temperature in °C; (2) Actual vapour pressure (AVP) from SVP and relative humidity: AVP = SVP × (RH / 100); (3) VPD = SVP − AVP. At 20°C with 60% RH: SVP = 2.34 kPa; AVP = 1.40 kPa; VPD = 0.94 kPa. At 30°C with 40% RH: SVP = 4.24 kPa; AVP = 1.70 kPa; VPD = 2.54 kPa. VPD doubles with a 10°C rise in temperature at constant RH — which is why high VPD and strong evaporative demand are features of hot summer days. Most weather station data software and irrigation scheduling apps calculate VPD automatically from temperature and humidity sensors.
How does VPD affect crop transpiration and stomatal conductance?
VPD is the primary driver of crop transpiration rate — the higher the VPD, the steeper the concentration gradient driving water vapour from inside the leaf (near saturation) to the drier atmosphere outside. Transpiration rate (T) is approximately proportional to VPD at constant stomatal conductance. However, stomata respond to VPD — as VPD increases, stomata partially close to limit water loss, reducing stomatal conductance (gs) and therefore CO₂ entry for photosynthesis. This creates a trade-off: high VPD drives both high potential transpiration and stomatal closure that reduces actual transpiration and CO₂ assimilation simultaneously. Under moderate water stress combined with high VPD (>2.5 kPa), stomatal closure can significantly reduce crop photosynthetic rate. See the transpiration entry and the stomatal conductance entry if available.
What is the ideal VPD range for spray application?
For herbicide and fungicide spray applications, VPD is a key application condition indicator alongside wind speed, temperature and inversion risk. Guidance: (1) VPD below 0.5 kPa: potentially adverse — low evaporation rate, risk of prolonged leaf wetness increasing fungal disease spread; may indicate high humidity conditions where inversions and spray drift risk are elevated; (2) VPD 0.5–2.0 kPa: generally favourable — droplets evaporate at a moderate rate, leaving adequate active ingredient in spray droplets reaching the target leaf; (3) VPD above 2.5–3.0 kPa: potentially adverse — rapid droplet evaporation reducing droplet size (increasing drift risk) and reducing the volume of active ingredient delivered to the leaf surface; volatile actives (glyphosate, some fungicides) are particularly sensitive to high VPD. Most UK spray application guidelines recommend applying between 09:00 and 17:00 on days with VPD below 3.0 kPa when possible.
How does VPD affect irrigation scheduling?
VPD is a component of reference evapotranspiration (ETo) — the standardised estimate of crop water demand used to schedule irrigation. The Penman-Monteith equation (the FAO standard for ETo calculation) uses VPD as one of four key meteorological inputs (alongside solar radiation, wind speed and temperature). Higher VPD directly increases ETo — a day with VPD of 2.0 kPa has approximately twice the evaporative demand of a day at 1.0 kPa, all else equal. For irrigation scheduling in UK vegetable and potato crops, ETo-based systems automatically account for VPD through the ETo calculation. Manual checks on VPD during periods of high temperature alert irrigators to higher-than-normal daily water demand that may require shorter trigger intervals or larger application volumes. See the effective rainfall entry and the growing degree days entry for related climate management terms.
What is the relationship between VPD and foliar disease risk in arable crops?
VPD (and its inverse, relative humidity) is a key factor in foliar fungal disease risk — most foliar pathogens require free water or very high humidity (RH >90%, VPD <0.3 kPa) on leaf surfaces for spore germination and infection. Low VPD conditions (high humidity, cool temperatures) are associated with higher disease infection risk because: leaf surfaces remain wet for longer after rain or dew events; spore germination and appressorial formation are more likely; hyphal growth post-infection is more rapid. The Septoria Risk Advisory System (AHDB/Rothamsted) and similar disease forecasting tools use RH/VPD as primary inputs in their infection risk models — periods of sustained low VPD with leaf wetness trigger infection period warnings. See the wheat disease management guide for the practical application in fungicide programme design.