Soil moisture deficit

SMD

The amount of water needed to bring the soil back to field capacity — the running total of crop water use minus rainfall since the soil was last at field capacity.

SMD is the practical currency of irrigation scheduling. Starting from field capacity (SMD = 0), the soil dries as the crop transpires and water evaporates. Effective rainfall and irrigation reduce the deficit. When SMD exceeds a crop-specific threshold (typically 25–50 mm for potatoes, 50–75 mm for cereals), yield begins to be lost. SMD is calculated daily: SMD(today) = SMD(yesterday) + ETc − effective rainfall − irrigation.

Irrigation scheduling data: see AHDB irrigation scheduling and FAO Irrigation & Drainage Paper 56.

Irrigation trigger (SMD threshold)

Lettuce
20 mm
Potato
25 mm
Onion
30 mm
Maize
40 mm
Cereals
50 mm
0102030405060 mm

Approximate trigger points. Source: AHDB.

Why it matters

SMD tells you when to start irrigating.

Irrigating too early wastes water and energy; too late causes yield loss and quality problems (hollow heart in potatoes, bolting in lettuce, poor grain fill in cereals). SMD gives you a clear, quantified trigger — when the deficit reaches the crop threshold, it is time to irrigate.

Running a daily water balance is the standard approach recommended by AHDB for all irrigated crops in the UK.

How to calculate it

Daily water balance: SMD today = yesterday + ETc - rain - irrigation.

Start from a known state — field capacity after winter drainage or a saturating rain event (SMD = 0). Each day, add crop evapotranspiration (ETc = ET0 x Kc) and subtract effective rainfall and any irrigation applied.

ET0 comes from weather station data (temperature, radiation, wind, humidity) using the Penman-Monteith equation. Kc values vary by crop and growth stage — published in FAO Paper 56.

FAQ

Frequently asked questions

What does soil moisture deficit mean in practice?
SMD is the amount of rain or irrigation (in mm) needed to bring the soil back to field capacity. An SMD of 0 means the soil is at field capacity — fully recharged. An SMD of 30 mm means the soil is 30 mm short of full, and you would need 30 mm of effective rain or irrigation to refill it. SMD rises as the crop transpires and the sun evaporates moisture; it falls when it rains or you irrigate.
How do you calculate soil moisture deficit?
Using a daily water balance: SMD today = SMD yesterday + ETc (crop evapotranspiration) - effective rainfall - irrigation applied. ETc is calculated from reference ET (from weather data) multiplied by a crop coefficient (Kc). You start the balance from a known point — typically field capacity after winter drainage or a heavy rain event. AHDB and Cranfield IRRIGUIDE provide tools to run these calculations automatically.
When should I start irrigating based on SMD?
When SMD reaches the crop-specific trigger point. Sensitive crops like lettuce and potatoes have low thresholds (20–25 mm) because they cannot tolerate even moderate water stress without quality or yield loss. Deeper-rooting crops like cereals tolerate higher deficits (40–50 mm). The trigger also depends on soil type — sandy soils with low available water capacity need irrigating sooner because their total water store is smaller.
How does soil type affect SMD and irrigation scheduling?
Soil type determines how much water the profile can hold (available water capacity, AWC). A sandy soil might hold 60–80 mm of available water in a 60 cm root zone, while a silt loam could hold 120–150 mm. On the sandy soil, a 25 mm SMD has already used a third of the available water; on the silt loam it is less than a fifth. This is why sandy soils require more frequent, smaller irrigation applications.
What is the difference between SMD and a tensiometer reading?
SMD is a calculated value from a water balance — it tells you how many mm of water are missing from the profile. A tensiometer measures soil water tension (in kPa or centibars) at a specific point — it tells you how hard the plant has to work to extract water. Both are useful: SMD is better for planning how much to apply; tensiometers are better for confirming when stress is approaching at a specific depth. Many growers use both together.
Who provides SMD data in the UK?
AHDB provides daily SMD estimates through their irrigation scheduling tools. Cranfield IRRIGUIDE is the standard commercial system used by many potato and vegetable growers. The Met Office publishes MORECS (Meteorological Office Rainfall and Evaporation Calculation System) data that underpins many SMD calculations. Some agronomists and irrigation consultants run bespoke water balance models for individual farms.