Harvest

Harvest Management Potatoes

Harvest Management Potatoes guide.

5 min read · Crops:

Harvest maturity indicators

IndicatorMethodReady signalNot ready
Skin set test Rub thumbnail across tuber skin Skin resists abrasion Skin peels or feathers easily
Haulm senescence Observe canopy colour and vigour Haulm yellow-brown, dying naturally Haulm still green and turgid
Tuber dry matter Dry matter % (hydrometer or lab) At or above target for end use Below minimum DM for crisping, chips or starch
Slug damage window Soil trap monitoring, tuber inspection Harvest before slugs significantly increase Delay risks accumulating internal damage
GDD accumulation Count growing degree days from planting GDD target reached for variety GDD below variety maturity threshold

Five-step harvest management programme

  1. 1
    Decide haulm destruction timing and method

    Haulm destruction initiates the skin set process by cutting off photosynthate supply to the tubers and reducing moisture at the soil surface. Timing depends on: (1) the required skin set period for the end use — crisping potatoes and long-term storage crops need 3–4 weeks minimum skin set; fresh market crops may be harvested sooner; (2) slug pressure — in high-slug-pressure fields, harvest before September peak activity; (3) blight risk — destroy haulm at least 3 weeks before harvest to remove sporulating tissue. Chemical desiccation (flufenacet, carfentrazone) or mechanical destruction (flail haulm topper) are the two main options. In organic crops, mechanical destruction only. Burning and rolling are rarely used today.

  2. 2
    Allow adequate skin set time

    Skin set time is the period between haulm destruction and harvest during which the tuber skin lignifies and toughens to resist harvest damage. Minimum skin set for long-term store: 2–3 weeks. Optimum for store quality: 3–4 weeks. During skin set, the soil must not be excessively wet (promotes secondary growth and lenticel disease) or very dry (increases harvest damage risk). Monitor soil temperature in the ridge during skin set — tubers below 10°C are at higher risk of bruising; above 25°C, quality deterioration accelerates.

  3. 3
    Assess and prepare the store before harvest begins

    Bring the store to the target intake temperature (10–12°C for most ware crops) before harvest begins. A cold store receiving warm tubers from a hot harvest risks condensation on tuber surfaces, promoting soft rots and silver scurf. Inspect the store for: pest infestation (moth, mite, wireworm in stored crop); old crop residues that could cross-contaminate; and the integrity of the ventilation system. The store health assessment matters as much as field management — quality lost in store cannot be recovered.

  4. 4
    Set the harvester to minimise bruising

    Potato bruising — both blackspot bruise (impact bruise on flesh) and skinning (surface abrasion) — occurs primarily at the harvester. Key harvester settings: elevator speed matched to ground speed to maintain gentle tuber flow; minimum drop heights at all transfer points (eliminate drops above 15 cm); shares set to lift the full ridge cleanly; and sieving set to remove soil without aggressive separation. Inspect the first loads carefully for any damage — correct immediately rather than allowing damage to accumulate. Soil temperature above 7°C reduces bruising risk significantly.

  5. 5
    Manage the curing and intake period in store

    The first 2–3 weeks after harvest is the curing period — critical for wound healing of surface damage and for the development of a protective periderm layer over damaged skin. During curing, hold the store at 15–18°C with high humidity (>95% RH) and good ventilation for 10–14 days, then cool slowly (1°C per week) to target storage temperature. Do not cool too fast — rapid chilling before wounds heal increases the entry points for storage rots. Consult the store management recommendations for your variety and intended storage duration.

Harvest damage — understanding and preventing it

The majority of quality damage in commercial potato production occurs at or shortly after harvest. Mechanical damage at the harvester (blackspot bruise, skinning), exposure to wet conditions post-harvest, and slug damage entering storage are the three primary risk factors. Managing them requires:

  • Soil temperature monitoring — delay harvest if soil temperature is below 7°C; check with a soil thermometer at ridge depth, not surface
  • Harvester calibration — check elevator speeds and drop heights before each field; adjust for crop and soil conditions
  • Load inspection — examine the first 5–10 tonnes of each field carefully for damage patterns; a damaged first load is a warning to correct settings immediately

For the pre-harvest pest context, see the slug management guide and the potato harvest and storing article. The potato agronomy guide covers the full agronomic season from planting to harvest.

Linking harvest quality to storage outcomes

Harvest quality and store management are inseparable — damage inflicted at harvest determines the store's disease pressure for the following 6–9 months. The most important outcome from good harvest management is a low-damage crop entering store with intact skin set and minimal slug holes. From that point, store temperature management and ventilation do the rest. For the storage side, PGRO storage guidance ↗ and AHDB potato storage guidance ↗ are the primary references. For the growing-degree-days context for harvest timing, see the growing degree days glossary entry and the harvest maturity entry.

Frequently asked questions

How do I know when potato skin set is complete?
The definitive skin set test is the thumbnail rub test: press your thumbnail firmly against the skin of a freshly dug tuber and drag it across the surface. If the skin resists without peeling or feathering, skin set is complete. If the skin lifts, shears or rolls away easily, continue to wait. Skin set typically takes 2–4 weeks after complete haulm destruction depending on soil temperature — cooler soils slow the process. In high-temperature conditions (>20°C soil), skin set accelerates but quality risks from bruising also increase. AHDB skin set guidance ↗ covers the assessment method in detail.
What is the difference between blackspot bruise and skinning damage?
Blackspot bruise is internal — caused by impact damage that ruptures cells in the cortex, triggering a melanin reaction visible as a dark discolouration in the flesh, often only apparent after peeling or cutting. It occurs primarily at transfer points in the harvester (elevator-to-box drops, in-store loading). Skinning is surface damage — the outer skin is scuffed or torn, leaving exposed parenchyma tissue vulnerable to infection. Skinning occurs at share entry points and at sieving separation. Both types of damage are temperature-dependent — cold, brittle tubers below 7°C bruise and skin far more readily than warmer tubers. AHDB potato quality guidance ↗ covers bruising assessment.
What temperatures should I target for long-term potato storage?
Target storage temperatures depend on end use:
  • Long-term ware (packing): 4–6°C
  • Seed potatoes: 3–4°C
  • Processing (crisps): 7–10°C (cold-induced sweetening is a risk below 7°C)
  • Processing (chips/fries): 5–8°C
Cold-induced sweetening — conversion of starch to reducing sugars at low temperature — causes darkening in frying and crisping end uses. PGRO storage guidance ↗ covers end-use-specific temperature management. See also the grain storage management guide for parallel principles in cereal storage.
How does slug damage affect the storage life of potatoes?
Slug holes in tubers are entry points for storage rots — primarily Pectobacterium and Dickeya soft rot bacteria that can spread rapidly through a store from infected tubers. Even small numbers of heavily slug-damaged tubers can trigger a store breakdown. Inspect harvest samples carefully for internal slug damage — damage is not always visible on the tuber surface. High-slug-risk fields (heavy soils, after OSR or cover crops) should be harvested early in the season or assessed with pre-harvest soil traps. See the slug management guide for the pre-harvest assessment framework, and the potato harvest and storing article for practical storage management.
When should I use chemical versus mechanical haulm destruction?
The choice between chemical and mechanical haulm destruction depends on: (1) blight status — if blight is present in the haulm, mechanical destruction risks spreading sporangia to tubers through soil disturbance; chemical desiccation is safer; (2) organic status — certified organic crops must use mechanical destruction only; (3) canopy bulk — thick, heavy canopies may not desiccate evenly with a single chemical application; topping may help; (4) cost and timing — mechanical toppers can be deployed faster than chemical programmes and allow harvest to begin in 1–2 days vs. the 2–3 week wait needed after chemical desiccation for full skin set. For blight context, see the potato blight control article and the potato agronomy guide.