Seed

Field emergence

The share of viable seeds sown that become established plants in the field.

Field emergence is always lower than laboratory germination. Seed placed in the field faces soil crusting, slug pressure, temperature fluctuations and variable seedbed contact that laboratory tests do not simulate. A typical field emergence factor is 85–95 % of germination — use your own experience and local conditions.

Factors reducing field emergence

FactorEffect on emergenceTypical loss
Seedbed quality Poor contact → reduced germination −5 to −20%
Seed depth Too deep → reduced emergence rate −3 to −15%
Soil moisture Deficit → dormancy; excess → damping off −5 to −25%
Soil temperature Below threshold → slow/failed germination −5 to −30%
Slug/pest pressure Seed excavation before emergence −5 to −30%
Soil-borne disease Pythium, Rhizoctonia damping off −2 to −15%

Why field emergence matters so much

Field emergence is often the most overlooked variable in seed rate calculations — and the one with the most variability. A grower who consistently uses 90% field emergence but whose fields average 75% will undersow by approximately 20% every year. Over time, this translates directly to sub-target plant populations, reduced yield potential in non-tillering crops (maize, oilseed rape), or the need for higher seed rates than the calculation suggests.

The corrective action is simple: measure emergence after drilling, build your own dataset by field and sowing condition, and update your default emergence factor accordingly. AHDB seed rate calculator ↗ includes adjustable field emergence inputs. See the seed rate glossary for the full formula and the wheat establishment guide for establishment counting methodology.

Improving field emergence

Targeted improvements: seedbed quality (fine, firm, consolidated — roll after drilling); seed placement (consistent depth 25–40 mm for cereals); slug control (pre-emergence ferric phosphate pellets on at-risk fields); drainage (waterlogged soils delay emergence and promote damping-off fungi); seed vigour (use recent-season seed with a vigour test if available; avoid storing cereal seed in damp conditions). Each improvement is multiplicative — addressing two factors simultaneously provides compounding benefit to final establishment counts. See the slug management guide for pest control and seed size and crop establishment for research context on vigour.

Frequently asked questions

How do I measure field emergence on my farm?
At the 4-leaf stage (GS14 for cereals), count emerged plants across five representative sites per field using a 0.5 m × 0.5 m quadrat (0.25 m²). Calculate plants/m² from your counts. Divide by the target plants/m² used in your seed rate calculation to get your actual field emergence factor. Repeat across multiple fields and seasons to build a reliable farm-specific dataset. AHDB seed rate guidance ↗ recommends this calibration approach as the most reliable way to improve seed rate accuracy over time. See also the plant population glossary entry for counting methodology.
What causes the gap between germination and field emergence?
Laboratory germination tests are conducted in optimal conditions — controlled temperature (20 °C), moisture and substrate. Field conditions add multiple stresses not present in the lab: variable soil-to-seed contact quality, slug and pest pressure, soil-borne disease (Pythium, Fusarium), temperature fluctuations, soil compaction, and moisture deficit or waterlogging. Each factor independently reduces the proportion of viable seeds that become established plants. The cumulative effect is that field emergence is consistently 5–20% below laboratory germination. NIAB seed quality guidance ↗ covers the relationship between laboratory tests and field performance.
How does seed vigour affect field emergence?
Seed vigour — distinct from germination percentage — measures the seed's physiological quality under stress conditions. High-vigour seed germinates and establishes quickly even in cold, wet or compacted soils; low-vigour seed (old seed, seed damaged by late harvest, heat or poor storage) may show 95% germination in a lab test but perform significantly worse under field stress. Vigour tests (ISTA cold test, Tetrazolium test, electrical conductivity test) better predict field performance than standard germination tests. See the seed size and crop establishment article and the germination rate glossary entry for context.
What is a typical field emergence figure for cereals?
Typical UK cereal field emergence: 85–90% in favourable conditions (September–early October, fine seedbed, no significant pest pressure); 75–85% in average conditions (October, normal seedbed); 65–75% in challenging conditions (late October onwards, cloddy seedbed, high slug risk, very wet or dry). Direct-drilled crops with no tillage sometimes achieve higher emergence than expected because the soil is undisturbed — but results are more variable. Use your own field records in preference to published averages. AHDB provides guidance ↗ on adjusting emergence estimates for different sowing conditions.
How do I use field emergence in my seed rate calculation?
Field emergence (expressed as a decimal) is the third input in the standard seed rate formula: Seed rate (kg/ha) = Target plants/m² × TGW(g) ÷ (Germination % × Field emergence %) × 100. Using a default field emergence of 90% when your farm average is 75% leads to undersowing by approximately 20% — a gap in plant population that cannot be recovered without tillering in cereals or at all in crops like maize. See the seed rate glossary entry and the wheat establishment guide for the full calculation and population targets.